Three Conductors

Model 305 Three Conductors, 4 Amps
Stainless steel ball bearing standard

305	3	0-250	4	200	<1m	1800	140 (60) /45(7)	100	>25M
305-L	3	0-250	4	200	<1m	1000	140 (60) /-20(-29)	100	>25M

"L" designator indicates  low temp. 

Model 305 Accessories

593 three contact receptacle w/ 6" wires (18 AWG)	553 three contact cap w/solder lugs
Receptacle used for mounting to rotating device. Accessories required for wire connections.  Order Separately.

Model 305 Connections

Model 305 Suggested Mounting Methods

Model 330 Three Conductors, 30 amps
Disconnects included (6 lg.) Boot Kit available Available with stainless steel ball bearing (330-SS)

330	3	0-250	30	100	<1m	1200	140 (60) /-20(-29)	300	>25M
330-SS	3	0-250	30	100	<1m	1200	140 (60) /-20(-29)	300	>25M

"SS" designator indicates stainless steel ball bearing  (recommended for wet or corrosive environments)

Model 330 Accessories

55251 Terminal 16 - 14 AWG (qty. 3 included)	57430 Boot Kit for dust or splash protection IP51
55253 Shrink Tube (qty. 3 included)	55252 Terminal 16 - 14 AWG (qty. 3 included)

Terminals for other wire gauges available. (22-18 AWG and 12-10 AWG)

Model 330 Standard Wire Connections

Model 330 Wire Connections With Optional Boot Kit

Model 330 Suggested Mounting Methods

Model 330 is typically mounted by either the black body or the white plastic bushing on either end using a set screw.  When mounting horizontally, mount the Mercotac so the body of the connector rotates.

Typical Body Mount Hole Dimensions MODEL HOLE DIAMETER (Ø) * DEPTH 330 et al 1.248"    (31.70) .80"    (20) Typical Bushing Mount Hole Dimensions 330 et al .625"    (15.88) .40"    (10) *Inch (mm) Tolerance Ø    +.001" (+.025)      -.000" (-.000)

Installation Notes: the up arrow should not point below horizontal do not solder to or bend connector tabs avoid lateral forces and mechanical loads (overly stiff or tight wires) do not rigid mount both ends of connector limit mounting eccentricity (runout / wobble) to .005" (.13mm) provide overload protection within the circuit avoid vibration and bumping motions

Model 331 Three Conductors, 2@4amps, 1@30amps
Disconnects included (4 sm., 2 lg.) Boot Kit available Available with stainless steel ball bearing (331-SS)

331	3	0-250	2@4/1@30	100	<1m	1800	140 (60) /-20(-29)	200	>25M
331-SS	3	0-250	2@4/1@30	100	<1m	1800	140 (60) /-20(-29)	200	>25M

"SS" designator indicates stainless steel ball bearing (recommended for wet or corrosive environments)

Model 331 Accessories

55251 Terminal 16 - 14 AWG (qty. 1 included)	57230 Boot Kit for dust / splash protection IP51
55250 16 - 14 AWG (qty. 1 included)	55110 22 - 18 AWG (qty. 4 included)

Terminals for other wire gauges available. (22-18 AWG and 12-10 AWG)

Model 331 Standard Wire Connections

Model 331 Wire Connections With Optional Boot Kit

Model 331 Suggested Mounting Methods

Model 331 is typically mounted by either the black body or the white plastic bushing on either end using a set screw.  When mounting horizontally, mount the Mercotac so the body of the connector rotates.

Typical Body Mount Hole Dimensions MODEL HOLE DIAMETER (Ø) * DEPTH 331 et al .998"    (25.35) .80"    (20) Typical Bushing Mount Hole Dimensions 331 et al .500"    (12.70) .40"    (10) *Inch (mm) Tolerance Ø    +.001" (+.025)      -.000" (-.000)

Installation Notes: the up arrow should not point below horizontal do not solder to or bend connector tabs avoid lateral forces and mechanical loads (overly stiff or tight wires) do not rigid mount both ends of connector limit mounting eccentricity (runout / wobble) to .005" (.13mm) provide overload protection within the circuit avoid vibration and bumping motions

Model 335 Three Conductors, 3@30amps & 500V
Disconnects included (6 lg.) Boot Kit available Available with stainless steel   ball bearing (335-SS)

335	3	0-500	30	100	<1m	500	140 (60) /-20(-29)	700	>50M
335-SS	3	0-500	30	100	<1m	500	140 (60) /-20(-29)	700	>50M

"SS" designator indicates stainless steel ball bearing (recommended for wet or corrosive environments)

Model 335 Accessories

57335 Boot Kit for dust or splash  protection IP51	55250 Terminal 16 - 14 AWG (qty. 3 included)	55251 Terminal 16 - 14 AWG (qty. 3 included)
Terminals for other wire gauges available. (22-18 AWG and 12-10 AWG)

Model 335 Standard Wire Connections

Model 335 Wire Connections With Optional Boot

Model 335 Suggested Mounting Methods

Model 335 is typically mounted by either the black body or the white plastic bushing on either end using a set screw.  When mounting horizontally, mount the Mercotac so the body of the connector rotates.

Typical Body Mount Hole Dimensions MODEL HOLE DIAMETER (Ø) * DEPTH 335, et al 1.575"    (40.0) .80"    (20.3) Typical Bushing Mount Hole Dimensions 335, et al .984"    (25.0) .80"    (20.3) *Inch  (mm) Tolerance Ø   +.001" (+.025)     -.000" (-.000)

Installation Notes: the up arrow should not point below horizontal do not solder to or bend connector tabs avoid lateral forces and mechanical loads (overly stiff or tight wires) do not rigid mount both ends of connector limit mounting eccentricity (runout / wobble) to .005" (.13mm) provide overload protection within the circuit avoid vibration and bumping motions